Rockhard 400

Buy Rockhard 400 Bhn Plate From Conquest Steel & Alloys

Rockhard 400 Bhn Abrasion Resistant Steel Plates are hard, wear-resistant steel plates built for equipment that faces constant sliding, impact and gouging. Conquest Steel & Alloys, a Mumbai steel plate stockist since 2008, supplies Rockhard 400 plates in a wide range of sizes, with cutting and ultrasonic testing support.

What Is Rockhard 400 Plate?

Definition : Rockhard 400 is a quenched-and-tempered abrasion resistant steel plate with a nominal hardness of 400 Brinell (BHN). Its hard martensitic structure resists sliding wear, impact and gouging in mining, cement and material-handling equipment.

Rockhard 400 plates are abrasion resistant (AR) steel plates, not corrosion-resistant plates. The alloy design gives them high surface hardness while keeping enough toughness to absorb impact. Engineers choose Abrasion Resistant Rockhard 400 Steel Plates to extend the life of liners, chutes, hoppers, buckets and cutting edges that wear out quickly in mild steel.

Benefits of Rockhard 400 BHN Plates

Rockhard 400 BHN plates extend equipment life, cut downtime and lower the total cost of ownership in abrasive working conditions. They give buyers a strong balance of hardness, toughness and workability, which is why Rockhard 400 plates are a common choice for wear parts across Indian industry.

1. High Wear Resistance - Rockhard 400 plates resist sliding abrasion far better than mild steel. Their nominal hardness of 400 BHN keeps rock, coal, ore, sand and cement from grinding the surface away quickly. This makes Rockhard 400 Wear Resistance Plates a practical upgrade for liners, chutes and hoppers that wear out fast.

2. High Strength - Rockhard 400 delivers a yield strength of about 140,000 psi (965 MPa) and a tensile strength of about 180,000 psi (1,241 MPa). These High Strength Rockhard 400 Plates carry heavy loads and resist deformation, so designers can often use thinner sections without losing performance.

3. Good Impact Toughness - Rockhard 400 absorbs impact better than harder grades such as Rockhard 500. This matters for equipment such as dump truck bodies, crusher liners and bucket floors, where falling material strikes the steel as well as sliding across it. The plate resists gouging and cracking under these mixed loads.

4. Easy Welding and Fabrication - Rockhard 400 welds and forms more easily than higher-hardness AR grades. Fabricators can cut, bend and weld it using standard procedures, provided they follow preheat and heat-input guidance based on the plate’s carbon equivalent (CEV). Conquest Steel & Alloys also supplies plates cut to size with plasma cutting or oxy-fuel cutting, which saves fabrication time.

5. Lower Total Cost of Ownership - A longer-lasting plate costs less over its working life, even if the price per kilogram is higher. Fewer replacements mean less downtime, less labour and fewer production stoppages. For mining, coal handling and concrete plants, this saving often outweighs the initial purchase price.

6. Wide Size Range - Rockhard 400 plates are available from 6 mm to 100 mm thick, up to 2,500 mm wide and 12,000 mm long. This range suits everything from thin liner sheets to thick structural wear parts. Buyers can also request custom sizes and shapes.

An Important Limit to Know

Rockhard 400 does not resist corrosion. It protects against wear, not rust. If your equipment also faces acids, seawater or constant moisture, tell our team. We will help you choose a suitable plate or protective system.

Common Applications

Rockhard 400 plates serve industries where material rubs, slides or strikes the steel surface. Typical uses include:

  • Mining machinery: bucket liners, dump truck bodies, crusher liners
  • Coal industry: coal chutes, hoppers, bunker liners
  • Concrete industry: mixer drums, batching plant wear parts
  • Metallurgy: material handling and slag-contact wear parts
  • Fan industry: fan blades and casing liners facing dust-laden air
  • Construction machinery: cutting edges, blade plates, bucket floors

Total cost of ownership often favours abrasion resistant plate. A plate that costs more per kilogram can last several times longer than mild steel, which cuts downtime and replacement labour.

Rockhard 400 Wear Resistance Plates vs. Corrosion Resistance

Wear resistance and corrosion resistance are different properties. Rockhard 400 resists material loss from abrasion, but it rusts in wet or chemical environments like any other carbon-alloy steel. For acids, seawater or chemical media, buyers should specify stainless steel, a coated plate or a weathering steel instead. If your equipment faces both abrasion and corrosion, tell our team and we will help you match the plate to the duty.

Rockhard 400 Plate Chemical Composition

The alloy content of Rockhard 400 rises with plate thickness. Thicker plates need more chromium, nickel and molybdenum to harden evenly through the section during quenching. Boron, in very small amounts, adds hardenability.

Thickness (mm)

Chemical Composition & Values

3–6

C: 0.15%, Si: 0.70%, Mn: 1.60%, P: 0.025%, S: 0.01%, Cr: 0.50%, Ni: 0.25%, Mo: 0.25%, B: 0.004%, CEV: 0.41, CET: 0.28

3–8

C: 0.15%, Si: 0.70%, Mn: 1.60%, P: 0.025%, S: 0.01%, Cr: 0.30%, Ni: 0.25%, Mo: 0.25%, B: 0.004%, CEV: 0.33, CET: 0.23

8–20

C: 0.15%, Si: 0.70%, Mn: 1.60%, P: 0.025%, S: 0.01%, Cr: 0.50%, Ni: 0.25%, Mo: 0.25%, B: 0.004%, CEV: 0.37, CET: 0.27

20–32

C: 0.18%, Si: 0.70%, Mn: 1.60%, P: 0.025%, S: 0.01%, Cr: 1.00%, Ni: 0.25%, Mo: 0.25%, B: 0.004%, CEV: 0.48, CET: 0.29

32–45

C: 0.22%, Si: 0.70%, Mn: 1.60%, P: 0.025%, S: 0.01%, Cr: 1.40%, Ni: 0.50%, Mo: 0.60%, B: 0.004%, CEV: 0.57, CET: 0.31

45–51

C: 0.22%, Si: 0.70%, Mn: 1.60%, P: 0.025%, S: 0.01%, Cr: 1.40%, Ni: 0.50%, Mo: 0.60%, B: 0.004%, CEV: 0.57, CET: 0.38

51–80

C: 0.27%, Si: 0.70%, Mn: 1.60%, P: 0.025%, S: 0.01%, Cr: 1.40%, Ni: 1.00%, Mo: 0.60%, B: 0.004%, CEV: 0.65, CET: 0.41

80–130

C: 0.32%, Si: 0.70%, Mn: 1.60%, P: 0.025%, S: 0.01%, Cr: 1.40%, Ni: 1.50%, Mo: 0.60%, B: 0.004%, CEV: 0.73, CET: 0.48

 

CEV and CET guide welding. A higher carbon equivalent means the plate needs more preheat and tighter heat-input control. Always confirm final values against the mill test certificate for your heat.

Rockhard 400 Plate Mechanical Properties

Rockhard 400 delivers about 400 BHN surface hardness with high strength. That combination defines Rockhard 400 Plates Brinell Hardness and explains why the plate resists wear better than structural steel.

Property Value
Yield strength 140,000 psi (about 965 MPa)
Tensile strength 180,000 psi (about 1,241 MPa)
Brinell hardness 400 BHN
Elongation 15% 
Reduction of area 60% 

These high-strength properties come from heat treatment. A High Strength Rockhard 400 Plates Supplier In India should always share the heat treatment condition and test certificate with every order. Conquest Steel & Alloys arranges documentation for quality records so your inspection team can verify each lot.


Does Rockhard 400 Work as a Low Temperature Plate?

Rockhard 400 is not sold as a dedicated low-temperature grade. Quenched-and-tempered plates keep useful toughness in cold conditions, but impact values depend on the heat and thickness. If you need Low Temperature Rockhard 400 Steel Plates, request a Charpy impact test requirement at order stage .


Other Types of Rockhard 400 Plate

Conquest Steel & Alloys supplies several forms of Rockhard 400 plate beyond standard sheets. These include:

  • Rockhard 400 steel weldable plates for fabricated wear parts
  • Rectangular abrasion resistant Rockhard 400 plates in standard and custom sizes
  • Rockhard 400 liner plates for chutes, hoppers and truck bodies
  • Rockhard 400 hot rolled plates for general wear applications
  • Rockhard 400 wear resistant plates cut to customer drawings

As a Rockhard 400 Hot Rolled Plates Dealer, we also cut sizes and shapes to your specification using plasma cutting and oxy-fuel cutting at our stockyards.


Rockhard 400 Plate vs. Rockhard 500 Plate

Rockhard 500 is harder than Rockhard 400, but Rockhard 400 is tougher and easier to weld and form. The right choice depends on whether your equipment fails by pure abrasion or by a mix of abrasion and impact.

Factor Rockhard 400 Rockhard 500
Nominal hardness About 400 BHN About 500 BHN
Wear life in pure sliding abrasion Good Longer
Impact toughness Higher Lower
Weldability and bending Easier More demanding
Typical duty Liners, buckets, chutes with impact Severe sliding wear with low impact

Choose Rockhard 400 when parts see impact and need forming or welding. Choose Rockhard 500 when abrasion dominates and the part stays flat. Our team will compare both grades against your duty before you order.

 

Leading Rockhard 400 Bhn Plate Manufacturers & Suppliers in India Since 2008: Conquest Steel & Alloys

Conquest Steel & Alloys is a Mumbai-based steel plate stockist and supplier, incorporated in 2008 and backed by 30 years of promoter experience in steel sourcing, stocking and supply chain. We work as a Rockhard 400 Plates Stockist and Rockhard 400 Plates Distributor, sourcing from mills that follow international plate production guidelines.

Our growth follows a clear timeline:

  • 2008: Headquarters opens at Khetwadi, Mumbai (750 sq. ft.). A 900 sq. m. stockyard opens at Kalamboli with two OET cranes and an oxy-fuel cutting facility.
  • 2011: A 3,000 sq. m. stockyard opens at Taloja with three 20-ton OET cranes, plus plasma and oxy-fuel cutting.
  • 2015: A 10,000 sq. m. warehouse opens at Taloja, half covered and half open, with stock capacity ten times the 2008 level.
  • 2024: Our Mumbai office at Khetwadi (1,500 sq. ft.) supports a team of 15 members.

Our quality process builds trust. Our in-house quality team performs ultrasonic testing (not destructive testing), and we arrange documentation for quality records. For buyers searching for a Rockhard 400 Wear Resistant Plates Stockholder or a Rockhard 400 Plates Stockist In Mumbai, India, this means stock you can see, test and collect or ship.


Indicative Price of Rockhard 400 Plates in India

Rockhard 400 plate typically falls in the ₹100 to ₹155 per kg range, depending on thickness and quantity. All figures below are indicative only and are not fixed quotes. Final prices depend on grade, thickness, quantity, processing and current market rates.

Product Form

Price Details

Rockhard 400 HR Plate

Thickness: 6–12 mm; Price: ₹100–₹135/kg (₹1,00,000–₹1,35,000/tonne)

Rockhard 400 HR Plate

Thickness: 12–40 mm; Price: ₹100–₹140/kg (₹1,00,000–₹1,40,000/tonne)

Rockhard 400 HR Plate

Thickness: 40–100 mm; Price: ₹110–₹155/kg (₹1,10,000–₹1,55,000/tonne)

Cut-to-Size Flats and Liner Parts

Plasma / oxy-fuel cutting; Processing: Plate rate + ₹5–₹15/kg (₹5,000–₹15,000/tonne)

Coil, Pipe, Tube

Not part of listed supply; Price: Not available

Always request a written quote before ordering. Market rates move, and import-grade plates can price above the range shown.


Conquest Steel & Alloys supplies - Global Network

Conquest Steel & Alloys supplies Rockhard 400 wear plates to buyers in India and in many overseas markets. Our supply list covers the Middle East (Saudi Arabia, Qatar, Oman, Kuwait, UAE, Bahrain), Africa (Nigeria, Kenya, Egypt, South Africa, Ghana), Asia (Malaysia, Singapore, Indonesia, Vietnam, South Korea, Japan, Bangladesh, Sri Lanka), Europe (Germany, United Kingdom, Poland, Italy, Netherlands) and the Americas (United States, Canada, Brazil, Mexico, Chile).

We also serve cities including Mumbai, Navi Mumbai, Pune, Chennai, Hyderabad, Ahmedabad, Kolkata, Dubai, Riyadh, Jeddah, Singapore, Houston and London. Ask our team about shipping options and documentation for your destination.


FAQ

What is Rockhard 400 plate used for?

Rockhard 400 plate protects equipment from abrasion and impact wear. Buyers use it for mining machinery, coal chutes, concrete plant parts, fan casings, construction machinery buckets and liner plates. It lasts longer than mild steel wherever material slides, strikes or grinds against the surface. 

What does 400 BHN mean?

BHN stands for Brinell Hardness Number. A 400 BHN rating means the plate surface resists indentation at about 400 on the Brinell scale. Higher hardness generally improves wear resistance, but very hard plates lose some toughness and formability. Rockhard 400 balances both for general wear duty. 

Is Rockhard 400 corrosion resistant?

No. Rockhard 400 is an abrasion resistant steel, not a corrosion-resistant one. It resists wear from sliding and impact but can rust in wet or chemical environments. For acid or seawater exposure, buyers should choose stainless steel, coated plate or weathering steel instead. 

Can Rockhard 400 plates be welded and cut?

Yes, with the right procedure. Welders should follow preheat and heat-input guidance based on the plate’s carbon equivalent (CEV), which rises with thickness. Conquest Steel & Alloys offers plasma cutting and oxy-fuel cutting, so you can receive plates cut to size. 

What sizes of Rockhard 400 plate does Conquest Steel & Alloys stock?

Conquest Steel & Alloys supplies Rockhard 400 plates from 6 mm to 100 mm thick, 1,500 mm to 2,500 mm wide and 6,000 mm to 12,000 mm long. We also cut custom sizes and shapes. Confirm current stock for your thickness before ordering. 

How do I get a quote for Rockhard 400 plates in India?

Send your thickness, width, length, quantity and delivery location to Conquest Steel & Alloys in Mumbai. Our team replies with a quote based on current grade, thickness and market rates. Prices on this page are indicative only, not fixed offers.

Contact Conquest Steel & Alloys for Rockhard 400 Plate at Best Price in India

Rockhard 400 Bhn Abrasion Resistant Steel Plates give equipment owners a practical way to cut wear, downtime and replacement cost. With a nominal hardness of 400 BHN, strength near 180,000 psi tensile and good weldability, these plates suit liners, chutes, hoppers, buckets and cutting edges across mining, coal, concrete, metallurgy and construction work.

Choosing the right plate takes more than picking a hardness number. You need to match thickness, heat treatment, chemistry and welding practice to your duty. If your equipment faces impact and needs forming or welding, Rockhard 400 is usually the better fit. If abrasion dominates, compare it with Rockhard 500. If corrosion is also a concern, specify a different material or a protective system, because Rockhard 400 does not resist rust.

Conquest Steel & Alloys has stocked, cut and supplied steel plates from Mumbai since 2008. Our Kalamboli and Taloja stockyards, overhead cranes, plasma and oxy-fuel cutting, in-house ultrasonic testing and quality documentation support give you stock you can verify before it ships. As a Rockhard 400 Wear Resistant Plates Stockholder and Rockhard 400 Hot Rolled Plates Dealer, we help you order the exact size you need instead of paying for scrap.

Ready to order? Send us your thickness, width, length, quantity and delivery location. We will reply with a clear, transparent quote based on current market rates. Request a quote or call our Mumbai team for a consultation today.

Rockhard 400 Specification:
India Price : Min- 95 INR Per Kg / Max- 180 INR Per Kg
USD Price : Min- 1.08 USD Per Kg / Max- 2.05 USD Per Kg
Grade : Rockhard 400
Type : Wear Resistant Steel Plate
Hardness : 370 – 430 HBW
Thickness : 6mm – 100mm
Width : Up to 3000mm
Length : Up to 12000mm
Yield Strength : ≥ 1000 MPA
Tensile Strength : 1250 – 1450 MPA
whatsapp-icon email-icon call-icon