ASTM A204 is a specification for molybdenum-alloyed carbon steel plate for welded boilers and pressure vessels. Molybdenum raises strength and creep resistance at elevated temperatures. Grades A, B and C differ in carbon content and strength.
ASTM 204 Grade A alloy steel plate, correctly written ASTM A204 Grade A, is the entry-strength grade of that specification. Conquest Steel & Alloys, a Mumbai-based stockist, supplier and exporter of alloy steel plates since 2008, supplies ASTM A204 / ASME SA204 plate in Grades A, B and C. Power, refining, chemical and oil and gas buyers use it for boilers, pressure vessels and heat-exchange equipment.
ASTM A204 Grade A is a molybdenum alloy steel plate with a minimum yield strength of 255 MPa and a tensile range of 450 to 585 MPa. It is also called a carbon-molybdenum or “Mo” steel. The ASME twin is SA204 Grade A.
Molybdenum is the key alloying element. It improves strength and creep resistance when equipment runs hot. Grade A carries the lowest carbon content of the three grades, which makes it the easiest of them to weld.
Buyers search for this material under many names, including ASTM 204 GRADE A, ASTM A 204 Grade A Alloy Steel Plate, ASTM A 204 Gr.A Alloy Steel Plate, Alloy Steel Plate ASTM A 204 Grade A and ASME SA204 Gr.A. They all point to the same grade. The ASTM A204 Grade B alloy steel plate and Grade C sit in the same specification with higher strength.
The plate is fully killed steel and ships normalised or as rolled. Fully killed practice removes dissolved oxygen, which supports soundness and weldability.
Many buyers search for “A204 plate manufacturers in Mumbai”. Conquest is a stockist and supplier, not a mill. We source plates from mills that follow international plate production guidelines, then stock, cut and dispatch them from our Mumbai-region yards.
The main features are elevated-temperature strength, the easiest weldability in the A204 family and a clean, uniform plate surface.
1. Strength at Elevated Temperature - Molybdenum improves creep resistance, so the plate keeps its load-bearing ability in hot service. Design codes set the allowable stress at each temperature, and your engineer should check the limits for your duty.
2. Moderate Strength for Lighter-Duty Pressure Equipment - Grade A delivers 255 MPa minimum yield strength and 450 to 585 MPa tensile strength. That suits vessels and boiler parts where Grade B or C strength is unnecessary. Specifying the lowest adequate grade also keeps fabrication simpler.
3. Good Weldability - Grade A has the lowest carbon limit of the three grades, and the steel is fully killed. Fabricators weld it with approved procedures. Thicker sections usually need preheat and, where the code requires it, post-weld heat treatment.
4. Clean Surface and Tight Fit-Up - Normalised and hot rolled plate arrives with an even surface that cuts, forms and rolls cleanly. Our cutting to size service reduces scrap and handling.
5. Long Service Life When Specified Correctly - The grade lasts when you match it to its service. It is a low-alloy steel, not a stainless steel, so wet or chemical duty needs coatings, linings or corrosion allowances.
A design note: carbon-molybdenum steels can suffer graphitisation after very long exposure at the top of their temperature range. For new high-temperature designs, review chromium-molybdenum alternatives with your engineer.
ASTM A204 covers three grades, A, B and C, supplied from 5 mm to 150 mm thick. The table summarises the specification we quote for ASTM A204 Grade A alloy steel plate.
| Parameter | Value |
|---|---|
| Grade | ASTM A204 Grade A alloy steel plate |
| Standard | ASTM A204 / ASME SA204 |
| Available grades | A, B, C |
| Thickness | 5 mm to 150 mm |
| Width | 1,250 mm to 2,500 mm |
| Length | 6,000 mm to 12,000 mm |
| Yield strength (min) | 255 MPa |
| Tensile strength | 450 to 585 MPa |
| Supply condition | Normalised or as rolled; fully killed |
Estimate plate weight with one formula: thickness (mm) × width (m) × length (m) × 7.85. A 16 mm × 2 m × 6 m plate weighs about 1,507.2 kg. Mill tolerances change the final figure, so treat this as a budgeting tool and confirm on the dispatch document.
ASTM A204 A/B/C is most often cross-referenced to EN 10028-2 16Mo3 and DIN 15Mo3. The table shows the usual equivalent designations. Each is a reference only, because chemistry and strength limits differ between standards.
| Region | Standard | Equivalent designation |
|---|---|---|
| USA (ASTM) | ASTM | A204 A / B / C |
| USA (ASME) | ASME | SA204 A / B / C |
| EU | EN 10028-2 | 16Mo3 |
| Germany | DIN | 15Mo3 / 16Mo3 |
| Japan | JIS | STBA12 |
| France | AFNOR | 15D3 |
| England | BS | 1503-243B / 240 / 243 |
| Italy | UNI | 15Mo3 / 16Mo3 |
A204 and 16Mo3 are close, not identical. Their molybdenum limits and strength steps differ, so confirm the match against your design code and the mill test certificate. JIS STBA12 is a tube-oriented designation in many references, so check the plate equivalent before you quote it.
ASME SA204 Grade A equals ASTM A204 Grade A in grade and chemistry, with 450 to 585 MPa tensile and 255 MPa minimum yield. The ASME edition carries the Section II stamp that boiler and pressure vessel codes require.
| Region | Standard | Equivalent designation |
|---|---|---|
| USA (ASTM) | ASTM | A204 A (ASTM 204 GRADE A) |
| USA (ASME) | ASME | SA204 A (ASME SA204 Gr.A) |
| EU | EN 10028-2 | 16Mo3 |
| Germany | DIN | 15Mo3 |
| Japan | JIS | STBA12 |
| France | AFNOR | 15D3 |
| England | BS | 1503-243B / 240 / 243 |
| Italy | UNI | 15Mo3 |
Grade A pairs a low-carbon, molybdenum-bearing chemistry with 450 to 585 MPa tensile strength. Heat analysis and test results on the mill test certificate govern every order.
| Element | Grade A (%) |
|---|---|
| Carbon (C), plate up to 25 mm | 0.18 max |
| Manganese (Mn) | 0.90 max |
| Phosphorus (P) | 0.025 max |
| Sulphur (S) | 0.025 max |
| Silicon (Si) | 0.15 to 0.40 |
| Molybdenum (Mo) | 0.45 to 0.60 |
Carbon limits rise in thicker plate. Grades B and C allow more carbon for higher strength.
| Property | Grade A value |
|---|---|
| Tensile strength | 450 to 585 MPa |
| Yield strength (min) | 255 MPa |
| Elongation in 50 mm (min) | 23% |
| Elongation in 200 mm (min) | 19% |
| Maximum plate thickness | 150 mm |
Strength rises from Grade A to Grade C, and carbon content rises with it. Pick the lowest grade that meets your design, because higher strength also asks more of your welding procedure.
| Grade | Tensile strength (MPa) | Yield strength, min (MPa) | Typical fit |
|---|---|---|---|
| ASTM A204 Grade A alloy steel plate | 450 to 585 | 255 | Lighter-duty vessels and boiler parts |
| ASTM A204 Grade B alloy steel plate | 485 to 620 | 275 | General boiler and pressure vessel work |
| ASTM A204 Grade C alloy steel plate | 515 to 655 | 295 | Higher-strength demands, thinner sections |
Grade A is the usual choice when the design does not need the extra strength of B or C.
ASTM A204 plate serves industries that run pressure and heat together. Typical uses include:
Match each use to its service conditions. Corrosive, sour or hydrogen duty needs a separate material review.
Conquest supplies every A204 grade and many related designations. Our team handles enquiries for:
We also arrange related chromium-molybdenum grades such as EN 10028 13CrMo4-5 and 10CrMo9-10 on enquiry. Those belong to a different family from A204, so confirm the grade your design needs.
Indicative A204 plate pricing in Mumbai runs roughly ₹125 to ₹150 per kg (₹1,25,000 to ₹1,50,000 per tonne). Every figure is indicative and depends on grade, thickness, quantity, cutting and market rates. None is a fixed quote.
| Product form | Grade | Indicative range (₹ per kg) | Indicative range (₹ per tonne) |
|---|---|---|---|
| Alloy steel plate | ASTM A204 Grade A | 125 to 150 | 1,25,000 to 1,50,000 |
| Alloy steel plate | ASTM A204 Grade B | 125 to 150 | 1,25,000 to 1,50,000 |
| Alloy steel plate | ASTM A204 Grade C | 125 to 150 | 1,25,000 to 1,50,000 |
A204 is a plate specification, so the table covers plate only. For coil, pipe or tube in related alloy grades, send an enquiry
Conquest Steel & Alloys has supplied steel plates from Mumbai since 2008. It draws on 30 years of promoter and partner experience in steel sourcing, stocking and supply chain. Buyers know us as a distributor, stockist and dealer of ASTM A204 Grade A, B and C alloy steel plates across India.
Our footprint grew step by step:
What this means for your order:
Our plan is to add a dedicated logistics team to cut delivery costs for customers.
Conquest supplies ASTM A204 alloy steel plate across India and to export markets.
All exports are subject to applicable trade rules.
ASTM groups plate standards by application. A36 covers structural plate, A516 covers carbon steel pressure vessel plate, A387 covers chromium-molybdenum plate and A204 covers molybdenum alloy plate. A572 serves high-strength structural work, and A240 serves stainless plate. Match the standard to your pressure, temperature and design code.
ASTM A240 is a stainless steel plate, sheet and strip standard, and ASME SA-240 is its direct counterpart. Grades 304 and 316 correspond to EN 10088 numbers 1.4301 and 1.4401. A240 does not equal A204. A204 Grade A is a molybdenum alloy plate for boilers and pressure vessels, not a stainless steel.
Grade A is the lower-strength, lower-carbon option in ASTM A204. It offers 450 to 585 MPa tensile and 255 MPa minimum yield, against 485 to 620 MPa and 275 MPa for Grade B. Grade A welds more easily, while Grade B carries higher design loads. Both suit boilers and pressure vessels.
Alloy steel falls into low-alloy and high-alloy families. Low-alloy examples include ASTM A204 (molybdenum), A387 (chromium-molybdenum), 4130 and 4140. High-alloy examples include stainless grades 304 and 316. Within A204, Grade A, B and C step up in carbon content and strength, and Grade A sits lowest.
ASTM A204 Grade A alloy steel plate gives fabricators a dependable, easy-to-weld molybdenum alloy option for boilers and pressure vessels. Its 450 to 585 MPa tensile range and 255 MPa minimum yield strength suit lighter-duty designs, and molybdenum helps the plate hold strength at elevated temperatures. Choosing the correct grade, A, B or C, keeps your design code, cost and weldability in balance.
Choosing the right supplier matters as much as choosing the right grade. Conquest Steel & Alloys has served steel buyers from Mumbai since 2008, backed by 30 years of promoter and partner experience in steel sourcing, stocking and supply chain. We stock plates at our Kalamboli and Taloja yards, cut to size on request, run ultrasonic testing in-house and arrange documentation for quality records.
Before you order, send us your drawing or cutting list, the required grade, thickness, width and length, the quantity, and your delivery location. State whether you need the mill test certificate with the dispatch and which code, ASTM A204 or ASME SA204, your design follows. We will confirm availability and share an indicative price, then convert it into a formal quote once the details are final.
Ready to move? Request a quote today. Call our Mumbai sales team on +91 22 23894572 (Monday to Saturday, 10 am to 6 pm) or email csa@csteel.in with your requirement. Our team will respond with stock status, lead time and pricing for ASTM A204 Grade A alloy steel plate. Whether you need one plate or a full project lot, we are ready to help.
Request a quote today. Send your grade, thickness, width, length, quantity and delivery location. Our Mumbai team replies with stock status and an indicative price.
| India Price : | Min- 125 INR Per Kg / Max- 150 INR Per Kg |
|---|---|
| USD Price : | Min- 1.43 USD Per Kg / Max- 1.71 USD Per Kg |
| Grade : | ASTM A204 Grade A |
| Material : | Molybdenum Alloy Steel |
| Thickness : | 6mm to 100mm |
| Width : | 1000mm to 3000mm |
| Length : | Up to 12000mm |
| Yield Strength : | ≥ 275 MPa |
| Tensile Strength : | 480 – 620 MPa |
| Molybdenum Content : | 0.45% |
| Applications : | Boilers, Pressure Vessels, Heat Exchangers |
| Standards : | ASTM A204 / ASME SA204 |